Search HexFastener

Find the part. Understand the spec.

Engineering Guide · 3 min read

More Carbon for Heat Treatment: SAE 1035, 1045 and 1050 under J403

Compare SAE 1030, 1035, 1038, 1040, 1045 and 1050, with 1060–1095 context: composition ranges, hardening potential and forming tradeoffs.

November 15, 2026HexFastener

The short answer: SAE 1035, 1045 and 1050 add progressively more carbon, increasing potential hardened strength while making cold forming more demanding.

A quenched-and-tempered stud needs its required condition through the shank as well as a sound formed head. A low-carbon blank may form readily yet lack the carbon needed for the intended hardened condition. That is where the medium-carbon 10xx grades become useful.

From SAE 1030 to 1050

These grades remain in the 10xx plain-carbon family under SAE J403. Their defining change is the carbon interval. In the selected rows below, Mn stays at 0.60–0.90%, which makes the effect of the carbon specification particularly clear. [1] [2]

GradeC (%)Mn (%)
10300.28–0.340.60–0.90
10350.32–0.380.60–0.90
10380.35–0.420.60–0.90
10400.37–0.440.60–0.90
10420.40–0.470.60–0.90
10450.43–0.500.60–0.90
10500.48–0.550.60–0.90

Heat analysis, mass percent; selected elements, not a complete purchase specification. Selected C/Mn ranges. The same table lists P ≤0.030% and S ≤0.050% for these rows. Silicon and delivery condition belong in the order. [2]

1035 and 1038 occupy the lower-carbon side of this group; 1040 and 1042 sit between them and 1045. The intervals overlap. 1050 moves the carbon window higher again, but its designation still describes chemistry rather than one guaranteed hardness or tensile strength. [2]

What the extra carbon buys

During suitable quenching, higher carbon increases the hardness that martensite can develop. Tempering then trades some of that hardness for the ductility and toughness needed in service. Compared with 1006–1022 steels, the medium-carbon group offers a stronger starting chemistry for parts intended to be hardened throughout a suitably sized section. [3]

The carbon intervals below show the move from 1022 through the medium-carbon grades and into the higher-carbon spring and wear range. Neighboring intervals overlap even as the overall carbon level rises.

Selected SAE 10xx carbon intervals, redrawn from CSC §6.1.16. Higher carbon increases hardening potential; the plot gives no tensile-strength prediction.
Selected SAE 10xx carbon intervals, redrawn from CSC §6.1.16. Higher carbon increases hardening potential; the plot gives no tensile-strength prediction. [2]

More carbon increases hardness potential; hardenability determines how far that response reaches into the part. A thick 1045 section can cool too slowly at its center to develop the same structure as its surface. A small section and a large section therefore need different heat-treatment assessments even when their grade names match. [3]

Why the forming route changes

More carbon generally makes cold deformation more demanding. For a substantial cold upset, the processor may need spheroidize-annealed stock: carbides are prepared in a rounded form that makes the steel easier to deform. The sequence is then stock preparation, forming, hardening and tempering to the finished specification. [3]

For a machined pin or stud, a different starting condition may be convenient. A grade sold annealed, cold drawn or quenched and tempered can require different cutting parameters and subsequent operations. Put the supplied condition beside “1045” on the order.

Where 1060, 1070, 1080 and 1095 belong

The 10xx series continues into compositions used for spring and wear applications. These grades are useful context when buying spring elements or hardened strip parts, but increasing the carbon this far adds forming and toughness tradeoffs that an ordinary bolt may not need. [3]

GradeC (%)Mn (%)
10600.55–0.650.60–0.90
10700.65–0.750.60–0.90
10800.75–0.880.60–0.90
10950.90–1.030.30–0.50

Heat analysis, mass percent; selected elements, not a complete purchase specification. Selected higher-carbon grades provide context for spring and wear parts. P ≤0.030% and S ≤0.050% in this source. A grade alone sets no spring or finished-fastener strength. [2]

1060 and 1070 remain below the carbon levels of 1080 and 1095. A spring requirement also depends on section, heat treatment, surface condition and geometry. Select these higher-carbon grades for the actual spring or wear specification, rather than treating them as a routine upgrade to 1045.

Choose carbon first, then check the section

For a medium-carbon fastener candidate, establish the final hardness and mechanical requirements, then confirm that the actual section can harden adequately with the proposed quench. If the available carbon level is appropriate but the center hardens inadequately, 15xx manganese steels or 4037, 4140 and related alloy steels can offer a different hardenability route. Simply increasing carbon is not the only option.

Keep the raw-material grade, supplied condition, part dimensions and final heat-treated requirements together on the drawing or RFQ. That combination gives the manufacturer a usable material instruction.

References

  1. SAE J403_202402 — Chemical Compositions of SAE Carbon Steels (stabilized February 2024)
  2. China Steel Corporation, Bar & Wire Rods Product Manual (2025), §§6.1.2, 6.1.16–6.1.18, pp. 13, 23–25
  3. Metallus, Practical Data for Metallurgists, 19th edition (2024), pp. 4–7 and glossary