Engineering Guide · 3 min read
Steel for Turned Parts: SAE 1117, 1144, 1215 and 12L14 (J403)
SAE 11xx and 12xx free-machining grades compared by C, Mn, P, S and Pb, including 1144 processing and the meaning of L in 12L14.
The short answer: SAE 11xx and 12xx steels use deliberate sulfur, phosphorus or lead additions to improve machining, making them a separate choice from cold-heading stock.
A threaded component turned from bar can spend more time being cut than being formed. That changes the material priority: a free-machining steel can improve chip control and cutting behavior, even though the same chemistry may be unsuitable for a demanding cold-heading operation.
11xx, 12xx and the L in 12L14
The SAE 11xx family uses intentional sulfur additions. The 12xx group uses sulfur and phosphorus together; L identifies an added lead range, as in 12L14. These are carbon-steel families associated with SAE J403, selected primarily for machining behavior. [1] [2]
Sulfur promotes sulfide inclusions that help chips break during cutting. Lead provides another machining aid in leaded grades. The improvement concerns the cutting process; the material still needs the strength, ductility and other properties required by the finished part. [3]
1117, 1141, 1144 and 1215 composition
In these grades, sulfur changes from a restricted residual element to a deliberately specified range. 1215 also specifies a phosphorus range.
| Grade | C (%) | Mn (%) | P (%) | S (%) |
|---|---|---|---|---|
| 1117 | 0.14–0.20 | 1.00–1.30 | ≤0.030 | 0.08–0.13 |
| 1141 | 0.37–0.45 | 1.35–1.65 | ≤0.030 | 0.08–0.13 |
| 1144 | 0.40–0.48 | 1.35–1.65 | ≤0.030 | 0.24–0.33 |
| 1215 | ≤0.09 | 0.75–1.05 | 0.04–0.09 | 0.26–0.35 |
Heat analysis, mass percent; selected elements, not a complete purchase specification. Selected producer-handbook ranges labeled SAE J403-24. Sulfur is an intentional range in these grades; 1215 also specifies a phosphorus range. [4]
1117 combines relatively low carbon with higher manganese and 0.08–0.13% S. 1141 and 1144 carry more carbon; 1144 also raises sulfur to 0.24–0.33%. 1215 keeps carbon at a maximum of 0.09% and uses a different P/S design for machining stock. [4]
The sulfur comparison below shows why “low-carbon steel” alone gives too little information about the manufacturing route.
What 12L14 adds
The following reference row lists lead explicitly. Keep Pb in the order and certificate when the grade requires it.
| Grade | C max. (%) | Mn (%) | P (%) | S (%) | Pb (%) |
|---|---|---|---|---|---|
| 12L14 | 0.15 | 0.85–1.15 | 0.04–0.09 | 0.26–0.35 | 0.15–0.35 |
Published composition limits, mass percent; selected elements, not a complete purchase specification. Producer reference chemistry, cross-checked against the NESSteel data sheet; Pb denotes lead. Use this row with the specified bar condition and customer material restrictions. [5]
12L14 is a resulfurized, rephosphorized leaded machining steel. The 0.15–0.35% Pb interval distinguishes it from nonleaded choices such as 1215. Select a leaded grade only when the customer’s material requirements permit it. [6]
Why 1144 and Stressproof are different instructions
1144 gives a chemistry designation. Stressproof is Niagara LaSalle’s product based on modified 1144 and a defined cold-drawing and stress-relieving process. For a turned stud, pin or spacer designed around that product’s properties, specify the product and supplied condition alongside the chemistry. [7]
Choose the machining route deliberately
Free-machining steel improves manufacture by cutting; cold-heading steel supports manufacture by deformation. The inclusions that aid machining also affect ductility and toughness, so a free-machining substitution needs assessment against the actual forming strain and service requirements. [8]
For a bar-machined component, specify grade, bar condition, dimensions, final strength or hardness, and any required material restrictions. For a heavily headed screw or bolt, begin with low-carbon 10xx or the appropriate boron-steel family and the required heading-quality stock.
References
- SAE J402_202403 — New Steel Designation System for Wrought or Rolled Steel (stabilized March 2024)
- SAE J403_202402 — Chemical Compositions of SAE Carbon Steels (stabilized February 2024)
- Bhardwaj et al., Comparative Machinability of Bloom Cast Free Cutting Steels, SAE Technical Paper 970520 (1997)
- China Steel Corporation, Bar & Wire Rods Product Manual (2025), §§6.1.2, 6.1.16–6.1.18, pp. 13, 23–25
- Kobe Steel, Wire Rods and Bars — Specification Tables, p. 40, free-cutting steels
- NESSteel, 12L14 Cold Roll Steel data sheet (2025)
- Niagara LaSalle, Stressproof Facts — 1144 modified and the cold-drawing/stress-relieving process
- Metallus, Practical Data for Metallurgists, 19th edition (2024), pp. 4–7 and glossary

